Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The EMD 567 16cyl Prime Mover was one of the most widely used Prime Movers in the world! From F-Units to Geeps this popular power house can still be found in many locomotives riding the rails today.
We have provided 2 versions of the prime mover in the sound file.
With Transition and without Manual Transition!
Transition is the process by which the transmission of a diesel-electric locomoitve is brought from series wiring to parallel wiring. When in series, all current in the locomotive pass through all motors: this produces maximum low-speed force in the motors, i.e., maximum starting torque. When in parallel, current is divided among the motors: this produces maximum high-end efficency, i.e., highest motor speed. In the Early EMD 567 prime movers this could be done manually. There was a throttle lever and a transition lever on the control stands. When the engineer made transition there was a very distinct sounds of the prime mover winding down to idle then up again quickly from Idle to the throttle notch. Not all locomotives can make transition -- yard locomotives are often wired only for series. Also many locomotives were equipped with automatic transitions that occured at a high rate of speed. This classic sound of "Manual Transition" is not heard in these engines the same way as it is in the early 567s. In Fact, it is best to check your prototype as this manual transistion sound could arguably be stated to be wrong for more than it is right for! Due to this fact we have made our sound with the ability to switch between these options so you can have the proper prime mover sounds for your prototype. By simply changing 1 CV (CV 48) you can choose one or the other.
As with All Select sound files this contains up to 16 different Horns, including so newly edited ones!
This LokSound Select file contains two versions of the prime mover:
Prime mover #1 (CV48=0) features a "EMD 567 16cyl with Normal Transition"
Prime mover #2 (CV48=16) features a "EMD 567 16cyl with Manual"
Locomotives:
FP7
FP9
FL9
FT
F2
F3
F7
F9
GP7
GP8
GP9
GP10
GP11
BL2
GP18
GP28
SD7
SD9
SD18
SD28
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 567C with Normal Transistion
CV48=16 EMD 16cyl 567C with Manual Transistion
Uses our OLD-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan Single Chime
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie S3L #1
CV48=8 Leslie A125
CV48=9 Leslie A200
CV48=10 Leslie RS3K
CV48=11 Hancock Air Whistle
CV48=12 Wabco E2
CV48=13 Nathan M3H
CV48=14 Leslie S2M
CV48=15 Leslie Dual A125-A200
Bells:
CV48=0 Steel Bell
CV48=64 Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 64
0 - EMD 16cyl 567C
0 - Nathan Single Chime
64 - Bronze Bell
Total 0+0+64 = 64
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/
